|
Physical Properties | Original Value | Comments |
---|
Density | 1.10 - 3.80 g/cc |
| 1.10 - 1.49 g/cc @Temperature 325 - 325 °C |
Filler Content | 3.00 - 60.0 % |
Water Absorption | 0.0200 - 10.0 % |
Moisture Absorption at Equilibrium | 0.0200 - 3.20 % |
| 0.850 - 1.35 % @Temperature 70.0 - 70.0 °C |
Water Absorption at Saturation | 0.160 - 5.90 % |
Additive Loading | 4.00 - 60.0 % |
Viscosity | 6.00 - 27.0 cP @Temperature 330 - 340 °C |
| 6.00 - 27.0 cP @Load 1.20 - 2.16 kg |
Viscosity Number | 105 - 120 cm³/g |
Maximum Moisture Content | 0.0300 - 0.100 |
Linear Mold Shrinkage | 0.0000200 - 0.0250 cm/cm |
Linear Mold Shrinkage, Transverse | 0.000100 - 0.0300 cm/cm |
Melt Flow | 5.00 - 80.0 g/10 min |
Spiral Flow | 30.0 - 53.0 cm |
|
Mechanical Properties | Original Value | Comments |
---|
Hardness, Rockwell M | 105 |
Hardness, Rockwell R | 100 - 127 |
Ball Indentation Hardness | 230 - 360 MPa |
Tensile Strength, Ultimate | 42.0 - 1040 MPa |
| 14.0 - 340 MPa @Temperature -40.0 - 250 °C |
Tensile Strength, Yield | 24.8 - 307 MPa |
| 20.0 - 140 MPa @Temperature 90.0 - 175 °C |
Elongation at Break | 0.500 - 150 % |
| 1.00 - 92.0 % @Temperature -40.0 - 200 °C |
Elongation at Yield | 1.00 - 50.0 % |
| 3.10 - 10.0 % @Temperature -40.0 - 150 °C |
Modulus of Elasticity | 1.70 - 102 GPa |
| 0.270 - 32.0 GPa @Temperature -40.0 - 200 °C |
Flexural Yield Strength | 3.15 - 527 MPa |
| 9.00 - 352 MPa @Temperature -40.0 - 200 °C |
| 96.0 - 181 MPa @Temperature 100 - 200 °C |
| 96.0 - 181 MPa @Strain 3.50 - 5.00 % |
Flexural Modulus | 1.50 - 44.8 GPa |
| 0.400 - 20.0 GPa @Temperature -40.0 - 200 °C |
Flexural Strain at Break | 1.80 - 3.50 % |
| 3.10 - 5.30 % @Temperature 80.0 - 200 °C |
Compressive Yield Strength | 100 - 336 MPa |
| 71.0 - 355 MPa @Temperature -40.0 - 200 °C |
Poissons Ratio | 0.290 - 0.410 |
Fatigue Strength | 100 - 100 MPa @# of Cycles 316 - 1580 |
| 100 - 100 MPa @Temperature 140 - 140 °C |
Shear Modulus | 0.852 - 5.18 GPa |
| 0.350 - 4.00 GPa @Temperature 0.000 - 350 °C |
Shear Strength | 44.1 - 108 MPa |
Secant Modulus | 1.70799 - 14.8867 GPa @Temperature 0.000 - 200 °C |
| 1.70799 - 14.8867 GPa @Strain 0.0500 - 4.13 % |
Izod Impact | 26.0 - 170 J |
Izod Impact, Notched | 0.147 - 11.0 J/cm |
| 0.910 - 7.50 J/cm @Temperature -40.0 - -40.0 °C |
Izod Impact, Unnotched | 0.801 - 5340 J/cm |
Izod Impact, Notched (ISO) | 2.00 - 115 kJ/m² |
| 3.00 - 75.0 kJ/m² @Temperature -40.0 - -20.0 °C |
Izod Impact, Unnotched (ISO) | 12.0 kJ/m² - NB |
| 23.0 kJ/m² - NB @Temperature -40.0 - -5.00 °C |
Charpy Impact Unnotched | 0.473 J/cm² - NB |
| 1.40 - 999.9 J/cm² @Temperature -40.0 - 0.000 °C |
Charpy Impact, Notched | 0.100 J/cm² - NB |
| 0.300 - 7.00 J/cm² @Temperature -40.0 - 0.000 °C |
Gardner Impact | 6.33 - 13.1 J |
Dart Drop, Total Energy | 1.36 - 54.2 J |
Falling Dart Impact | 2.90 - 15.6 J |
Instrumented Impact Total Energy | 1.48 - 4.37 J |
Coefficient of Friction | 0.0460 - 0.590 |
Coefficient of Friction, Static | 0.0490 - 0.620 |
Tensile Creep Modulus, 1 hour | 5500 - 11000 MPa |
Tensile Creep Modulus, 1000 hours | 5000 - 10000 MPa |
K (wear) Factor | 5.50 - 10100 x 10-8 mm³/N-M |
Dynatup @ -18°C | 43.0 - 66.0 J |
Dynatup @ -18°C Max Load | 408000 - 662000 g |
|
Electrical Properties | Original Value | Comments |
---|
Electrical Resistivity | 0.0500 - 1.00e+17 ohm-cm |
Surface Resistance | 10.0 - 8.10e+16 ohm |
Static Decay | 2.00 sec |
Dielectric Constant | 3.20 - 6.20 |
| 4.20 - 136 @Temperature 60.0 - 200 °C |
| 4.20 - 136 @Frequency 1000 - 1.00e+6 Hz |
Dielectric Strength | 16.0 - 45.0 kV/mm |
| 0.800 - 27.5 kV/mm @Temperature 60.0 - 200 °C |
Dissipation Factor | 0.00297 - 0.0500 |
| 0.0100 - 0.850 @Temperature 60.0 - 200 °C |
| 0.0100 - 0.850 @Frequency 1000 - 1.00e+6 Hz |
Arc Resistance | 115 - 300 sec |
High Voltage Arc Resistance to Ignition (HVAR) | 0.000 - 150 sec |
Comparative Tracking Index | 100 - 800 V |
Hot Wire Ignition, HWI | 60.0 - 150 sec |
High Amp Arc Ignition, HAI | 60.0 - 120 arcs |
High Voltage Arc-Tracking Rate, HVTR | 0.000 - 80.0 mm/min |
|
Thermal Properties | Original Value | Comments |
---|
CTE, linear | 5.20 - 97.0 µm/m-°C |
| 6.00 - 190 µm/m-°C @Temperature -40.0 - 250 °C |
CTE, linear, Transverse to Flow | 4.50 - 105 µm/m-°C |
| 33.0 - 160 µm/m-°C @Temperature -40.0 - 250 °C |
Specific Heat Capacity | 1.05 - 1.74 J/g-°C |
| 2.40 - 2.90 J/g-°C @Temperature 325 - 325 °C |
Thermal Conductivity | 0.230 - 20.0 W/m-K |
| 0.240 - 0.250 W/m-K @Temperature 325 - 325 °C |
Melting Point | 223 - 340 °C |
Maximum Service Temperature, Air | 120 - 290 °C |
Deflection Temperature at 0.46 MPa (66 psi) | 88.0 - 320 °C |
Deflection Temperature at 1.8 MPa (264 psi) | 80.0 - 320 °C |
Deflection Temperature at 8.0 MPa | 60.0 - 250 °C |
Vicat Softening Point | 100 - 313 °C |
Glass Transition Temp, Tg | 45.0 - 144 °C |
UL RTI, Electrical | 65.0 - 150 °C |
UL RTI, Mechanical with Impact | 50.0 - 140 °C |
UL RTI, Mechanical without Impact | 65.0 - 150 °C |
Flammability, UL94 | HB - 5VA |
| V-0 - V-0 @Temperature 1.50 - 1.50 °C |
Flame Spread | 25.0 - 80.0 mm/min |
Oxygen Index | 23.0 - 42.0 % |
Glow Wire Test | 675 - 960 °C |
|
Optical Properties | Original Value | Comments |
---|
Transmission, Visible | 20.0 - 38.0 % |
Reflection Coefficient, Visible (0-1) | 0.900 |
|
Processing Properties | Original Value | Comments |
---|
Processing Temperature | 280 - 345 °C |
Nozzle Temperature | 280 - 345 °C |
Melt Temperature | 240 - 360 °C |
Mold Temperature | 48.9 - 190 °C |
Drying Temperature | 79.4 - 150 °C |
Moisture Content | 0.0200 - 0.200 % |
Dew Point | -31.7 - -28.9 °C |
Injection Pressure | 41.4 - 124 MPa |
Some of the values displayed above may have been converted from their original units and/or rounded in order to
display the information in a consistent format. Users requiring more precise data for scientific or engineering
calculations can click on the property value to see the original value as well as raw conversions to equivalent units.
We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding
error. We also ask that you refer to MatWeb's
terms of use regarding this information.
Click here to go back to viewing the property data in MatWeb's normal format.