|
Physical Properties | Metric | English | Comments |
---|
Density | 1.27 - 1.76 g/cc | 0.0459 - 0.0636 lb/in³ |
| 1.31 - 1.49 g/cc @Temperature 223 - 250 °C | 0.0473 - 0.0538 lb/in³ @Temperature 433 - 482 °F |
Filler Content | 5.00 - 32.0 % | 5.00 - 32.0 % |
Water Absorption | 0.000 - 4.00 % | 0.000 - 4.00 % |
Moisture Absorption at Equilibrium | 0.0500 - 0.500 % | 0.0500 - 0.500 % |
Water Absorption at Saturation | 0.150 - 0.500 % | 0.150 - 0.500 % |
Viscosity | 150 - 3.50e+6 cP @Temperature 230 - 270 °C | 150 - 3.50e+6 cP @Temperature 446 - 518 °F |
| 150 - 3.50e+6 cP @Shear Rate 1.00 - 100000 1/s | 150 - 3.50e+6 cP @Shear Rate 1.00 - 100000 1/s |
Viscosity Number | 62.0 - 112 cm³/g | 0.620 - 1.12 dl/g |
Maximum Moisture Content | 0.0200 | 0.0200 |
Linear Mold Shrinkage | 0.000500 - 0.0200 cm/cm | 0.000500 - 0.0200 in/in |
| 0.00300 - 0.00400 cm/cm @Temperature 260 - 260 °C | 0.00300 - 0.00400 in/in @Temperature 500 - 500 °F |
| 0.00300 - 0.00400 cm/cm @Pressure 60.0 - 60.0 MPa | 0.00300 - 0.00400 in/in @Pressure 8700 - 8700 psi |
Linear Mold Shrinkage, Transverse | 0.00100 - 0.0180 cm/cm | 0.00100 - 0.0180 in/in |
| 0.0110 - 0.0130 cm/cm @Temperature 260 - 260 °C | 0.0110 - 0.0130 in/in @Temperature 500 - 500 °F |
| 0.0110 - 0.0130 cm/cm @Pressure 60.0 - 60.0 MPa | 0.0110 - 0.0130 in/in @Pressure 8700 - 8700 psi |
Melt Flow | 1.00 - 75.0 g/10 min | 1.00 - 75.0 g/10 min |
Ash | 0.0350 - 30.0 % | 0.0350 - 30.0 % |
|
Mechanical Properties | Metric | English | Comments |
---|
Hardness, Rockwell M | 70.0 - 100 | 70.0 - 100 |
Hardness, Rockwell R | 90.0 - 120 | 90.0 - 120 |
Ball Indentation Hardness | 160 - 235 MPa | 23200 - 34100 psi |
Tensile Strength, Ultimate | 15.0 - 154 MPa | 2180 - 22300 psi |
Tensile Strength, Yield | 68.0 - 150 MPa | 9860 - 21800 psi |
Elongation at Break | 0.900 - 50.0 % | 0.900 - 50.0 % |
Elongation at Yield | 2.50 - 9.00 % | 2.50 - 9.00 % |
Modulus of Elasticity | 0.765 - 21.2 GPa | 111 - 3070 ksi |
Flexural Yield Strength | 70.3 - 230 MPa | 10200 - 33400 psi |
Flexural Modulus | 1.86 - 11.3 GPa | 270 - 1640 ksi |
Flexural Strain at Break | 3.00 - 3.50 % | 3.00 - 3.50 % |
Flexural Strain at Yield | 2.20 - 4.90 % | 2.20 - 4.90 % |
Poissons Ratio | 0.330 - 0.350 | 0.330 - 0.350 |
Izod Impact, Notched | 0.267 - 4.27 J/cm | 0.500 - 8.00 ft-lb/in |
| 0.300 - 0.450 J/cm @Temperature -20.0 - -20.0 °C | 0.562 - 0.843 ft-lb/in @Temperature -4.00 - -4.00 °F |
Izod Impact, Unnotched | 0.490 - 9.61 J/cm | 0.919 - 18.0 ft-lb/in |
Izod Impact, Notched (ISO) | 3.00 - 10.0 kJ/m² | 1.43 - 4.76 ft-lb/in² |
| 7.00 - 10.0 kJ/m² @Temperature -30.0 - -30.0 °C | 3.33 - 4.76 ft-lb/in² @Temperature -22.0 - -22.0 °F |
Izod Impact, Unnotched (ISO) | 20.0 - 55.0 kJ/m² | 9.52 - 26.2 ft-lb/in² |
| 20.0 - 55.0 kJ/m² @Temperature -30.0 - -30.0 °C | 9.52 - 26.2 ft-lb/in² @Temperature -22.0 - -22.0 °F |
Charpy Impact Unnotched | 2.30 - 8.00 J/cm² | 10.9 - 38.1 ft-lb/in² |
| 1.20 - 7.50 J/cm² @Temperature -40.0 - -20.0 °C | 5.71 - 35.7 ft-lb/in² @Temperature -40.0 - -4.00 °F |
Charpy Impact, Notched | 0.230 - 2.00 J/cm² | 1.09 - 9.52 ft-lb/in² |
| 0.180 J/cm² - NB @Temperature -40.0 - -20.0 °C | 0.857 ft-lb/in² - NB @Temperature -40.0 - -4.00 °F |
Tensile Impact Strength | 8.00 - 55.0 kJ/m² | 3.81 - 26.2 ft-lb/in² |
Tensile Creep Modulus, 1 hour | 5000 - 11000 MPa | 725000 - 1.60e+6 psi |
Tensile Creep Modulus, 1000 hours | 3000 - 8000 MPa | 435000 - 1.16e+6 psi |
|
Electrical Properties | Metric | English | Comments |
---|
Electrical Resistivity | 1000 - 1.00e+18 ohm-cm | 1000 - 1.00e+18 ohm-cm |
Surface Resistance | 1000 - 1.00e+17 ohm | 1000 - 1.00e+17 ohm |
Dielectric Constant | 3.00 - 4.50 | 3.00 - 4.50 |
Dielectric Strength | 16.0 - 44.0 kV/mm | 406 - 1120 kV/in |
Dissipation Factor | 0.00100 - 0.0220 | 0.00100 - 0.0220 |
Arc Resistance | 60.0 - 120 sec | 60.0 - 120 sec |
Comparative Tracking Index | 125 - 600 V | 125 - 600 V |
Hot Wire Ignition, HWI | 7.00 - 120 sec | 7.00 - 120 sec |
High Amp Arc Ignition, HAI | 30.0 - 120 arcs | 30.0 - 120 arcs |
|
Thermal Properties | Metric | English | Comments |
---|
CTE, linear | 20.0 - 67.0 µm/m-°C | 11.1 - 37.2 µin/in-°F |
| 16.0 - 20.0 µm/m-°C @Temperature 55.0 - 160 °C | 8.89 - 11.1 µin/in-°F @Temperature 131 - 320 °F |
CTE, linear, Transverse to Flow | 50.0 - 120 µm/m-°C | 27.8 - 66.7 µin/in-°F |
| 140 - 140 µm/m-°C @Temperature 55.0 - 160 °C | 77.8 - 77.8 µin/in-°F @Temperature 131 - 320 °F |
Specific Heat Capacity | 1.60 - 1.60 J/g-°C @Temperature 250 - 250 °C | 0.382 - 0.382 BTU/lb-°F @Temperature 482 - 482 °F |
Thermal Conductivity | 0.173 - 0.202 W/m-K | 1.20 - 1.40 BTU-in/hr-ft²-°F |
| 0.260 - 0.260 W/m-K @Temperature 250 - 250 °C | 1.80 - 1.80 BTU-in/hr-ft²-°F @Temperature 482 - 482 °F |
Melting Point | 200 - 250 °C | 392 - 482 °F |
Maximum Service Temperature, Air | 90.0 - 215 °C | 194 - 419 °F |
Hot Ball Pressure Test | 165 - 220 °C | 329 - 428 °F |
Deflection Temperature at 0.46 MPa (66 psi) | 138 - 225 °C | 280 - 437 °F |
Deflection Temperature at 1.8 MPa (264 psi) | 70.0 - 250 °C | 158 - 482 °F |
Deflection Temperature at 8.0 MPa | 65.0 - 165 °C | 149 - 329 °F |
Vicat Softening Point | 165 - 225 °C | 329 - 437 °F |
Glass Transition Temp, Tg | 55.0 °C | 131 °F |
UL RTI, Electrical | 75.0 - 140 °C | 167 - 284 °F |
UL RTI, Mechanical with Impact | 75.0 - 140 °C | 167 - 284 °F |
UL RTI, Mechanical without Impact | 75.0 - 140 °C | 167 - 284 °F |
Flammability, UL94 | HB - 5VA | HB - 5VA |
Oxygen Index | 28.0 - 40.0 % | 28.0 - 40.0 % |
Glow Wire Test | 675 - 960 °C | 1250 - 1760 °F |
|
Processing Properties | Metric | English | Comments |
---|
Processing Temperature | 204 - 270 °C | 400 - 518 °F |
Nozzle Temperature | 225 - 270 °C | 437 - 518 °F |
Melt Temperature | 220 - 280 °C | 428 - 536 °F |
Mold Temperature | 30.0 - 130 °C | 86.0 - 266 °F |
Drying Temperature | 80.0 - 140 °C | 176 - 284 °F |
Moisture Content | 0.000 - 0.300 % | 0.000 - 0.300 % |
Dew Point | -40.0 - -28.9 °C | -40.0 - -20.0 °F |
Injection Pressure | 4.96 - 120 MPa | 720 - 17400 psi |
Vent Depth | 0.00127 - 0.00381 cm | 0.000500 - 0.00150 in |
Some of the values displayed above may have been converted from their original units and/or rounded in order to
display the information in a consistent format. Users requiring more precise data for scientific or engineering
calculations can click on the property value to see the original value as well as raw conversions to equivalent units.
We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding
error. We also ask that you refer to MatWeb's
terms of use regarding this information.
Click here to view
all the property values for this datasheet as they were originally entered into MatWeb.