|
Physical Properties | Metric | English | Comments |
---|
Density | 1.11 - 1.57 g/cc | 0.0401 - 0.0567 lb/in³ |
| 1.19 - 1.36 g/cc @Temperature 205 - 250 °C | 0.0430 - 0.0491 lb/in³ @Temperature 401 - 482 °F |
Filler Content | 5.00 - 13.0 % | 5.00 - 13.0 % |
Water Absorption | 0.0300 - 0.500 % | 0.0300 - 0.500 % |
Moisture Absorption at Equilibrium | 0.00400 - 0.350 % | 0.00400 - 0.350 % |
Water Absorption at Saturation | 0.300 - 0.450 % | 0.300 - 0.450 % |
Viscosity Test | 80.0 - 145 cm³/g | 0.800 - 1.45 dl/g |
Viscosity Number | 100 - 120 cm³/g | 1.00 - 1.20 dl/g |
Maximum Moisture Content | 0.0200 | 0.0200 |
Linear Mold Shrinkage | 0.00100 - 0.0200 cm/cm | 0.00100 - 0.0200 in/in |
| 0.00800 - 0.00800 cm/cm @Temperature 260 - 260 °C | 0.00800 - 0.00800 in/in @Temperature 500 - 500 °F |
| 0.00800 - 0.00800 cm/cm @Pressure 60.0 - 60.0 MPa | 0.00800 - 0.00800 in/in @Pressure 8700 - 8700 psi |
Linear Mold Shrinkage, Transverse | 0.00110 - 0.0170 cm/cm | 0.00110 - 0.0170 in/in |
| 0.0140 - 0.0140 cm/cm @Temperature 260 - 260 °C | 0.0140 - 0.0140 in/in @Temperature 500 - 500 °F |
| 0.0140 - 0.0140 cm/cm @Pressure 60.0 - 60.0 MPa | 0.0140 - 0.0140 in/in @Pressure 8700 - 8700 psi |
Melt Flow | 4.00 - 60.0 g/10 min | 4.00 - 60.0 g/10 min |
Ash | 7.00 - 13.0 % | 7.00 - 13.0 % |
|
Mechanical Properties | Metric | English | Comments |
---|
Hardness, Rockwell M | 83.0 - 120 | 83.0 - 120 |
Hardness, Rockwell R | 117 - 119 | 117 - 119 |
Hardness, Shore D | 81.0 | 81.0 |
Ball Indentation Hardness | 160 - 170 MPa | 23200 - 24700 psi |
Tensile Strength, Ultimate | 45.0 - 110 MPa | 6530 - 16000 psi |
| 50.0 - 130 MPa @Temperature -20.0 - 100 °C | 7250 - 18900 psi @Temperature -4.00 - 212 °F |
Tensile Strength, Yield | 49.0 - 100 MPa | 7100 - 14500 psi |
Elongation at Break | 2.00 - 75.0 % | 2.00 - 75.0 % |
Elongation at Yield | 3.70 - 4.00 % | 3.70 - 4.00 % |
Modulus of Elasticity | 2.80 - 6.90 GPa | 406 - 1000 ksi |
Flexural Yield Strength | 75.0 - 170 MPa | 10900 - 24700 psi |
| 50.0 - 50.0 MPa @Temperature 90.0 - 90.0 °C | 7250 - 7250 psi @Temperature 194 - 194 °F |
Flexural Modulus | 0.140 - 9.00 GPa | 20.3 - 1310 ksi |
Poissons Ratio | 0.350 - 0.360 | 0.350 - 0.360 |
Izod Impact, Notched | 0.267 - 1.60 J/cm | 0.500 - 3.00 ft-lb/in |
| 0.48051 - 0.48051 J/cm @Temperature -28.9 - -28.9 °C | 0.90019 - 0.90019 ft-lb/in @Temperature -20.0 - -20.0 °F |
Izod Impact, Unnotched | 3.20 - 9.61 J/cm | 6.00 - 18.0 ft-lb/in |
Izod Impact, Notched (ISO) | 3.80 - 23.0 kJ/m² | 1.81 - 10.9 ft-lb/in² |
| 3.00 - 10.0 kJ/m² @Temperature -30.0 - -30.0 °C | 1.43 - 4.76 ft-lb/in² @Temperature -22.0 - -22.0 °F |
Izod Impact, Unnotched (ISO) | 20.0 - 45.0 kJ/m² | 9.52 - 21.4 ft-lb/in² |
| 20.0 - 40.0 kJ/m² @Temperature -30.0 - -30.0 °C | 9.52 - 19.0 ft-lb/in² @Temperature -22.0 - -22.0 °F |
Charpy Impact Unnotched | 2.00 J/cm² - NB | 9.52 ft-lb/in² - NB |
| 2.00 - 19.0 J/cm² @Temperature -30.0 - -20.0 °C | 9.52 - 90.4 ft-lb/in² @Temperature -22.0 - -4.00 °F |
Charpy Impact, Notched | 0.230 - 1.80 J/cm² | 1.09 - 8.57 ft-lb/in² |
| 0.210 - 1.00 J/cm² @Temperature -30.0 - -20.0 °C | 0.999 - 4.76 ft-lb/in² @Temperature -22.0 - -4.00 °F |
Tensile Creep Modulus, 1 hour | 3000 - 5500 MPa | 435000 - 798000 psi |
Tensile Creep Modulus, 1000 hours | 2000 - 5000 MPa | 290000 - 725000 psi |
|
Electrical Properties | Metric | English | Comments |
---|
Electrical Resistivity | 1.00e+6 - 2.00e+17 ohm-cm | 1.00e+6 - 2.00e+17 ohm-cm |
Surface Resistance | 1.00e+6 - 1.00e+17 ohm | 1.00e+6 - 1.00e+17 ohm |
Dielectric Constant | 3.00 - 4.30 | 3.00 - 4.30 |
Dielectric Strength | 17.0 - 100 kV/mm | 432 - 2540 kV/in |
Dissipation Factor | 0.00100 - 0.0290 | 0.00100 - 0.0290 |
Dielectric Loss Index | 0.00200 - 0.0200 | 0.00200 - 0.0200 |
Arc Resistance | 60.0 - 180 sec | 60.0 - 180 sec |
Comparative Tracking Index | 125 - 600 V | 125 - 600 V |
Hot Wire Ignition, HWI | 7.00 - 120 sec | 7.00 - 120 sec |
High Amp Arc Ignition, HAI | 0.000 - 120 arcs | 0.000 - 120 arcs |
High Voltage Arc-Tracking Rate, HVTR | 25.4 - 150 mm/min | 1.00 - 5.91 in/min |
|
Thermal Properties | Metric | English | Comments |
---|
CTE, linear | 30.0 - 130 µm/m-°C | 16.7 - 72.2 µin/in-°F |
| 30.0 - 40.0 µm/m-°C @Temperature 50.0 - 120 °C | 16.7 - 22.2 µin/in-°F @Temperature 122 - 248 °F |
CTE, linear, Transverse to Flow | 80.0 - 140 µm/m-°C | 44.4 - 77.8 µin/in-°F |
| 120 - 160 µm/m-°C @Temperature 50.0 - 120 °C | 66.7 - 88.9 µin/in-°F @Temperature 122 - 248 °F |
Specific Heat Capacity | 1.60 - 1.97 J/g-°C | 0.382 - 0.471 BTU/lb-°F |
| 1.89 - 1.97 J/g-°C @Temperature 205 - 250 °C | 0.452 - 0.471 BTU/lb-°F @Temperature 401 - 482 °F |
Thermal Conductivity | 0.131 - 0.230 W/m-K | 0.909 - 1.60 BTU-in/hr-ft²-°F |
| 0.230 - 0.240 W/m-K @Temperature 205 - 250 °C | 1.60 - 1.67 BTU-in/hr-ft²-°F @Temperature 401 - 482 °F |
Melting Point | 200 - 226 °C | 392 - 439 °F |
Maximum Service Temperature, Air | 75.0 - 290 °C | 167 - 554 °F |
Deflection Temperature at 0.46 MPa (66 psi) | 113 - 225 °C | 235 - 437 °F |
Deflection Temperature at 1.8 MPa (264 psi) | 76.7 - 215 °C | 170 - 419 °F |
Deflection Temperature at 8.0 MPa | 55.0 - 70.0 °C | 131 - 158 °F |
Vicat Softening Point | 100 - 221 °C | 212 - 430 °F |
Glass Transition Temp, Tg | 45.0 - 60.0 °C | 113 - 140 °F |
UL RTI, Electrical | 50.0 - 140 °C | 122 - 284 °F |
UL RTI, Mechanical with Impact | 50.0 - 130 °C | 122 - 266 °F |
UL RTI, Mechanical without Impact | 50.0 - 140 °C | 122 - 284 °F |
Flammability, UL94 | HB - 5VA | HB - 5VA |
Flame Spread | 36.0 - 100 mm/min | 1.42 - 3.94 in/min |
Oxygen Index | 19.0 - 34.0 % | 19.0 - 34.0 % |
Glow Wire Test | 650 - 960 °C | 1200 - 1760 °F |
|
Processing Properties | Metric | English | Comments |
---|
Processing Temperature | 20.0 - 270 °C | 68.0 - 518 °F |
Nozzle Temperature | 238 - 277 °C | 460 - 530 °F |
Die Temperature | 240 - 270 °C | 464 - 518 °F |
Melt Temperature | 220 - 280 °C | 428 - 536 °F |
Mold Temperature | 26.7 - 130 °C | 80.0 - 266 °F |
Injection Velocity | 200 - 300 mm/sec | 7.87 - 11.8 in/sec |
Drying Temperature | 80.0 - 140 °C | 176 - 284 °F |
Moisture Content | 0.0200 - 0.200 % | 0.0200 - 0.200 % |
Dew Point | -28.9 °C | -20.0 °F |
Injection Pressure | 40.0 - 120 MPa | 5800 - 17400 psi |
Vent Depth | 0.00127 - 0.00254 cm | 0.000500 - 0.00100 in |
Some of the values displayed above may have been converted from their original units and/or rounded in order to
display the information in a consistent format. Users requiring more precise data for scientific or engineering
calculations can click on the property value to see the original value as well as raw conversions to equivalent units.
We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding
error. We also ask that you refer to MatWeb's
terms of use regarding this information.
Click here to view
all the property values for this datasheet as they were originally entered into MatWeb.